Gwengie's Civic is not like yours - Dodge Charger.
-
- Lvl3 Street Racer
- Posts: 287
- Joined: Sat Mar 06, 2010 4:02 pm
- Location: Wexford, Ireland
I have a set of those spacers here, think there 38mm..
I was going to use them on the front of my rear wheel drive 4g,
Still have'nt got around to building it though
I was going to use them on the front of my rear wheel drive 4g,
Still have'nt got around to building it though
91 Civic hatch,
B16a running Obd1,
96 Saloon VTi leather interior,
Crx dash and door cards,
Ef9 skirts and lips,
and loooooooads more.
B16a running Obd1,
96 Saloon VTi leather interior,
Crx dash and door cards,
Ef9 skirts and lips,
and loooooooads more.
-
- Lvl3 Street Racer
- Posts: 287
- Joined: Sat Mar 06, 2010 4:02 pm
- Location: Wexford, Ireland
Not at the moment man, i'll try find them and post a pic or two later
I was planning on using the engine, box and back axel from a 1977 mkII celica (1600 dohc on twin 45's).
The rear quarters would have to be made 3.5" wider on each side to suit the celica axel, so it would look savage with the spacers on the front
I was planning on using the engine, box and back axel from a 1977 mkII celica (1600 dohc on twin 45's).
The rear quarters would have to be made 3.5" wider on each side to suit the celica axel, so it would look savage with the spacers on the front
91 Civic hatch,
B16a running Obd1,
96 Saloon VTi leather interior,
Crx dash and door cards,
Ef9 skirts and lips,
and loooooooads more.
B16a running Obd1,
96 Saloon VTi leather interior,
Crx dash and door cards,
Ef9 skirts and lips,
and loooooooads more.
ah okgwenge wrote:I'm putting a bulge in it [=
Going to leave it open at the back too with some mesh in it.... Help evacuate some hot air.
Plus my bonnet on the car atm is mangled
Hadstec on crxuk has put a vent in the top of his VT bonnet. looks good, almost OEM. He got it from a Ford Transit van, might be worth looking into
Marc_VT:
HONDAB88:
4th-gen-ken:
Cool man i'll have a look. I think i'm going to add a "naca duct" above where the airfilter sits. And the bulge is like a more emthasised vtec bonnet [= If that makes sense haha!ah ok
Hadstec on crxuk has put a vent in the top of his VT bonnet. looks good, almost OEM. He got it from a Ford Transit van, might be worth looking into
HONDAB88:
I'll have a think about it When you say widebody guess you mean flared arches? Could bring my bumper out to meet the arches if i did that, would imagine it will look savage! Could even make the arch lower to make the wheels look really tucked haha!i put 15mm ones on my ef2 theyre ok with a 40mm drop and 205/50/15 . would look mean on your car with the widebody if you get me
4th-gen-ken:
That sounds sweet x2 in the picsNot at the moment man, i'll try find them and post a pic or two later
I was planning on using the engine, box and back axel from a 1977 mkII celica (1600 dohc on twin 45's).
The rear quarters would have to be made 3.5" wider on each side to suit the celica axel, so it would look savage with the spacers on the front
-
- Lvl3 Street Racer
- Posts: 287
- Joined: Sat Mar 06, 2010 4:02 pm
- Location: Wexford, Ireland
-
- Lvl3 Street Racer
- Posts: 287
- Joined: Sat Mar 06, 2010 4:02 pm
- Location: Wexford, Ireland