This is easy to do, and you do not need to jack the car up or take any wheels off.
1. First undo the screws at the back end holding it to a plastic bracket.
2. Then work your way to the front taking out all the screws. There are usually metal ones at each end.
3. Once you have taken out all the plastic screws and the plastic part they screw into, it should then swing loose.
4. Now to get it off the clips; you need to slide the skirt towards the front of the car, and it should pop off no problem.
5. To get the clips out the sill, turn them 90 degrees and they should pull out very easily
6. Attach the white clips to the skirt before you re-fit.
How To - Remove VT/siR sideskirts
How To - Remove VT/siR sideskirts
Last edited by Marc_EE9 on Mon Dec 14, 2009 9:07 pm, edited 1 time in total.
-
- Lvl3 Street Racer
- Posts: 428
- Joined: Fri Nov 05, 2010 6:58 pm
- Location: Rep. Of Ireland
Re: How To - Remove VT/siR sideskirts
HI lads, I just bought vt side skirts and i want to fit them to my JDM ef1. Now i bought front and rear lips in the past (vt lips) and there has been holes there for them to just bolt into. I was just wondering how would i go about fitting the side skirts? Is there any write up on how to do this i would appreciate if you could point me in the right direction. Cheers
Re: How To - Remove VT/siR sideskirts
tigerseal!
Or you have a lot of holes to make.
viewtopic.php?f=19&t=25961&start=30" onclick="window.open(this.href);return false;
Or you have a lot of holes to make.
viewtopic.php?f=19&t=25961&start=30" onclick="window.open(this.href);return false;
Re: How To - Remove VT/siR sideskirts
its not a lot of holes.
they need to be removable. if you tigerseal them, it will damage the paint etc if you have to get them off, and could trap dirt/water
they need to be removable. if you tigerseal them, it will damage the paint etc if you have to get them off, and could trap dirt/water
-
- Lvl3 Street Racer
- Posts: 428
- Joined: Fri Nov 05, 2010 6:58 pm
- Location: Rep. Of Ireland
Re: How To - Remove VT/siR sideskirts
Should i drill drill small pilot holes for screws is it marc? oh and biger holes for the clips to slot into?
Re: How To - Remove VT/siR sideskirts
Benny_d_man wrote:Should i drill drill small pilot holes for screws is it marc? oh and biger holes for the clips to slot into?
Personally I would do it as intended, using the original clips. If you drilled small holes it would be hard to rust proof inside where you drill as it will expose bare metal.
-
- Lvl3 Street Racer
- Posts: 428
- Joined: Fri Nov 05, 2010 6:58 pm
- Location: Rep. Of Ireland
Re: How To - Remove VT/siR sideskirts
Not following you to be honest man. Do it as intended? I have a few of the origianal clips but missing a few. Im just wondering should there holes under my sills to accommodate the skirts? like i said there was already holes in front and rear bumper for the vt lips to just bolt on.
Re: How To - Remove VT/siR sideskirts
Benny_d_man wrote:Not following you to be honest man. Do it as intended? I have a few of the origianal clips but missing a few. Im just wondering should there holes under my sills to accommodate the skirts? like i said there was already holes in front and rear bumper for the vt lips to just bolt on.
Do as intended... ie; fix them as they should be, as Honda did on VT's.
I only have 4 clips on each side, as the bodyshop lost the others
then yes, you have a bunch of holes for plastic screw clips to go in underneath