A9 CVC - My EE9 2.0i-VT - Now with 243hp B20

c16vivt · Post by **c16vivt** » Tue Feb 26, 2008 11:50 pm

thanks for link.....

seems you have done your homework..... a+

the b16b2 are slighty quicker, my brother has a ek4 vti..

good luch with your project mate..

EE9 CVC · Post by **EE9 CVC** » Wed Feb 27, 2008 12:01 am

c16vivt wrote:thanks for link.....

seems you have done your homework..... a+

the b16b2 are slighty quicker, my brother has a ek4 vti..

good luch with your project mate..

Thanks a lot

Not meaning to be rude but there is no B16B2, if it is an EK4 VTI then it will have a B16A2 which is still nothing compared to a B16B, but you are right the engine in the EK4, the B16A2 has 160hp compared to the B16A1 which has 150HP

WELLZ · Post by **WELLZ** » Wed Feb 27, 2008 12:20 am

B16b

Very nice! I couldn't sleep at night knowing it was outside on a pallet though

Are you going to swap the rockers over?

This car is going to be amazing!!

EE9 CVC · Post by **EE9 CVC** » Wed Feb 27, 2008 12:31 am

WELLZ wrote:B16b Very nice! I couldn't sleep at night knowing it was outside on a pallet though Are you going to swap the rockers over?

This car is going to be amazing!!

Thanks very much, I know what you mean, I can't wait to get it in, it should be safe enough though.

Only other place for it is my bedroom

Yeah I am going to swap the rocker covers over - I don't wont to loose my custom jobby

, I may get the new one done also at some time if I can think of something different to paint on.

It won't be any more amazing than yours will be!!! It looks like everything on yours is going to be perfect

WELLZ · Post by **WELLZ** » Wed Feb 27, 2008 12:46 am

I think its safe to say it would be in my bedroom now haha!

Its going to pull like a train!

EE9 CVC · Post by **EE9 CVC** » Thu Feb 28, 2008 11:02 pm

This arrived today!!

ITR Shift Boot - Real leather with nice red stiching

ITR shift boot - looks great, really smartens the interior up and matches the seats perfectly. Was not a direct fit though
as the ITR one is about 3.5cm longer than the EE9 one, I had to cut a few bits off the leather at the bottom and modify
it to fit my gaiter bracket.

Just got to get a Skunk2 Gear Knob now to set it off.

The engines a bit cleaner now also!!

WELLZ · Post by **WELLZ** » Thu Feb 28, 2008 11:40 pm

Matches the seats and exterior colour really well! Cant wait to fit mine. Thanks for the heads up on the fitment!

Engine looks really clean, especially the alternator brackets

EE9 CVC · Post by **EE9 CVC** » Thu Mar 06, 2008 2:30 am

Some boring but needed parts turned up today!

Bung for the Exhaust Manifold

New ECU to run the B16B on!

Along with another chip set up with launch Control!

Sorry for the bad quality photos

I am trying to get some parts from Honda at the min but Honda arn't very good at finding them, I knew more about
Honda parts than the parts guys did!!! No luck getting the notorious MTF either.

Post by **Tahir** » Thu Mar 06, 2008 11:04 am

this is going to be the best ukvt imo by far when its done!

mint as a mofo, loving the shiny red.

and the b16b..................

WELLZ · Post by **WELLZ** » Thu Mar 06, 2008 6:19 pm

Which Honda dealer are you using?

Let me know what bits and pieces you need? Might be able to help you out with part numbers!

EE9 CVC · Post by **EE9 CVC** » Thu Mar 06, 2008 8:19 pm

^^^^ After a lot of searching I managed to get part numbers for most of the parts I needed, but I could not
find part numbers for a B16B header Gasket and a 2.5 Inch Collector o-ring Gasket. I also need to find
where to get some MTF94!!!

EE9 CVC · Post by **EE9 CVC** » Thu Mar 06, 2008 8:34 pm

^^^^ Thanks, Yeah no luck with Honda so I was going to try Land Rover on Friday. Just need to find out if you can
use it with a Quaife LSD first as I know that some LSDs dont like it.

EE9 CVC · Post by **EE9 CVC** » Fri Mar 07, 2008 1:47 am

Took the intake manifold off last night and left it soaking in water overnight to soften the old gasket.
Managed to get it all off tonight and put it back on with the Hondata Intake Manifold Heatsheild Gasket.

I will try and get a photo of it in place tomorrow

EE9 CVC · Post by **EE9 CVC** » Tue Mar 11, 2008 1:59 am

Gasket On

EE9 CVC · Post by **EE9 CVC** » Tue Mar 11, 2008 2:09 am

Some new parts arrived today

Magnecor 8.5mm HT leads

Earthing Kit

Exhaust Heat Wrap

MTF 94!!

JDM EK9 N1 Crack Pulley - Very lightweight and properly balanced, made of Zinc Plated Chromoly Steel.
Better response and more power!!!

Replaces this big brute of a thing!!